Nov.16,2026
DX51D+ZF galvanized steel is a general-forming steel grade with a zinc-iron alloy coating, also known as galvannealed steel. Under EN 10346, DX51D identifies the substrate grade, while ZF specifies the alloyed zinc-iron coating.
Selecting DX51D+ZF requires more than confirming the steel designation. Coating mass, forming requirements, surface treatment, and subsequent welding or painting must also be considered.

DX51D+ZF is produced through continuous hot-dip galvanizing followed by alloying heat treatment. This additional process forms a zinc-iron intermetallic coating with a characteristic matte gray surface.
Rosen's published DX51D+ZF specifications include:
Yield Strength: 200–310 MPa
Tensile Strength: 280–420 MPa
Minimum Elongation (A80): 30%
Coating Type: ZF (Zinc-Iron Alloy)
Coating Mass Range: 80–120 g/m², both surfaces combined
Available Thickness: 0.5–2.5 mm
These figures are based on Rosen's published product specifications. Actual order requirements should be verified against the applicable standard and material test certificate.
DX51D+ZF is intended for general cold-forming operations, including conventional bending, profiling, and moderate stamping.
However, the DX51D substrate grade does not guarantee suitability for demanding deep-drawing operations.
For components involving substantial deformation, manufacturers should evaluate higher-formability grades such as DX53D+ZF or DX54D+ZF.
The zinc-iron alloy coating also requires consideration during forming. Excessive deformation or unfavorable tooling conditions may cause coating powdering or local damage.
Material qualification should therefore address both substrate formability and coating integrity.
The ZF designation identifies the coating type but does not independently define the coating mass.
For example, ZF100 and ZF120 represent different zinc-iron alloy coating mass designations. Under EN 10346, their specified minimum total coating masses are 100 g/m² and 120 g/m², respectively, measured across both surfaces using the prescribed triple-spot test.
A higher coating mass should not automatically be considered better. The specification must balance corrosion protection, coating integrity, and forming requirements.
Surface treatment also matters. Oiling, passivation, and other available treatments should be selected according to storage conditions, forming operations, and subsequent painting.
Before purchasing DX51D+ZF galvanized steel, confirm the following:
Material Standard: Specify the applicable EN 10346 edition and required steel grade.
Coating Designation: Identify ZF coating mass and any additional coating requirements.
Dimensions: Confirm thickness, width, sheet length or coil dimensions, and tolerances.
Surface Condition: Define surface treatment and any appearance requirements.
Processing Requirements: Confirm bending, stamping, resistance spot welding, or painting conditions.
Material Documentation: Request the applicable material test certificate and confirm the agreed acceptance requirements.
For production involving new stamping tools or coating systems, representative material trials are recommended before approving a specification change.
Rosen supplies Galvannealed Steel in different forming grades, coating specifications, and dimensions.
DX51D+ZF is available within Rosen's published galvannealed steel range in sheet and coil forms, subject to specific grade and dimension availability.
For accurate quotations, please provide the required steel grade, coating mass, thickness, width, quantity, surface treatment, and manufacturing application.
Contact Rosen to discuss DX51D+ZF Galvannealed Steel specifications for your production requirements.
Latest Blogs
Nov 16, 2026
Nov 16, 2026
Nov 16, 2026
Nov 16, 2026
Is galvannealed steel sheet as strong as regular steel sheet?
Contact Us
E-mail: partner@rosensteelga.com
Tel: +86-27-86615388
WhatsApp: +86 177 6252 7953
WeChat:Rosen17762527953
Add.: No. 1, 30th Floor, Building 1, Fuxing Huiyu Waterfront International, Sanjiao Road Village, Xujiapeng Street, Wuchang District, Wuhan City, Hubei Province,P.R.China